Skip to content
Vecaria
Go Pro

How to Validate an IFC File Online — Checks & IDS

A model that opens is not a model that is fit to send. An IFC file can load cleanly in a viewer and still be missing storeys, carry elements with no properties, use the wrong units, or fail the information requirements the receiver asked for — and every one of those faults surfaces after delivery, when fixing it costs the most. Validating an IFC file means checking it against requirements before you hand it over, and this guide explains what those checks are, which free tools run them online, and what to verify before every delivery.

“Validation” is not one check. It is six different layers, and a tool that does one of them well may not do the others at all. Knowing which layer you need is the first step, because it decides which tool to open.

Layer What it checks Typical tool
1. File compliance The file is a well-formed STEP physical file and conforms to the IFC EXPRESS schema (correct entity types, attributes, and references) buildingSMART Validation Service
2. Parsing and integrity The file loads without errors; every entity reference resolves; GlobalIds are present and unique Any IFC viewer that reports parse errors
3. IDS (information requirements) The model meets the receiver’s stated information requirements: required properties, classifications, values, and materials, as written in an IDS file IFC Viewer Online, Bimlyte, Model Checker
4. Data quality Names, types, and properties are filled in and consistent; elements sit on the right storey; units and project origin are sane; no orphaned or proxy elements where real ones are expected IFC Viewer Online (44 rules), Solibri
5. Geometry Solids are valid and closed where they should be; elements are not duplicated in the same place; bounding boxes are reasonable IfcOpenShell-based tools, Solibri
6. Rule checking and clash Project rules hold (for example, every door belongs to a wall opening); elements from different disciplines do not collide Solibri, BIMcollab Zoom, Navisworks

Most delivery failures live in layers 2–4: a file that parses but has missing properties, wrong storeys, or empty names. Full schema compliance (layer 1) matters when a contract or a submission portal requires it; clash detection (layer 6) is a coordination task, not a file-quality task, and usually needs more than one model.

BIM coordinators usually run delivery checks in three tiers, from cheap to expensive. Run them in order — there is no point checking information requirements on a file that does not parse.

Tier Question What it catches Cost
L1 — Schema Does the file conform to the IFC schema? Malformed STEP, wrong entity usage, broken references Free online (buildingSMART Validation Service)
L2 — Quality Is the data complete and consistent? Missing properties, empty names, wrong storeys, bad units Free online (IFC Viewer Online, Bimlyte)
L3 — IDS Does the model meet the agreed information requirements? Missing required properties, wrong classifications, wrong values Free online with an IDS file

A file that passes L1 and L2 is usually fit to send for informal coordination. A file that must pass a contractual handover — an ISO 19650 stage gate, a Singapore CORENET X submission (which has required three-layer checks since June 2026), or a public-procurement BIM delivery — needs L3 as well, with the receiver’s IDS file as the checklist.

How to check an IFC file before you deliver it

Section titled “How to check an IFC file before you deliver it”

You do not need desktop software for the first five steps. Everything below runs in a browser, and the first four need no account.

  1. Open it and read the parse report. Load the file in an IFC viewer. If the viewer reports parse errors, fix the export before anything else — a file that does not parse cleanly will fail every downstream check. Vecaria’s IFC Model Viewer opens IFC files entirely in the browser and shows parse errors on load.
  2. Check the spatial structure. Confirm the chain project → site → building → storey → element is complete, and that every element sits on a storey. Elements with no storey are the most common structural fault in exported models.
  3. Scan the element list. Open the element list and check for empty names, missing types, and proxy elements (IfcBuildingElementProxy) where a real element type is expected. A high proxy count usually means the exporter gave up on classifying geometry.
  4. Run a data-quality check. Load the file in a free online validator (see the comparison below) and read the health score and the problem list. Fix the highest-priority items first — missing GlobalIds, missing storeys, and missing required properties.
  5. Run your IDS file, if you have one. If the receiver sent an IDS file, run it against the model. Every failed specification is a delivery defect, even if the model looks fine in a viewer.
  6. Check geometry and clashes separately. Geometry validity and clash detection need heavier tools. For a single-model delivery, a bounding-box overlap scan catches the obvious duplicates; true clash detection across disciplines belongs in a coordination tool, not in a file check.

Every tool below is free for the checks listed. They differ in what they check, whether your file leaves your machine, and whether they need an account.

Tool What it checks Runs where Account Limits
buildingSMART Validation Service Schema compliance (L1) Server — file is uploaded Yes File size limit applies (around 250 MB); no 3D view; compliance only
IFC Viewer Online 44 data-quality rules, IDS 1.0, health score 0–100, one-click fixes Browser — file stays on your machine No Single-model checks; clash is a limited bounding-box scan
Bimlyte IDS 1.0, data quality Browser No IDS-focused
opensource.construction Model Checker IDS 1.0, rule checks Browser (Pyodide + IfcOpenShell) No Heavy first load; rule set is narrower than IFC Viewer Online
Solibri WebChecker Rule-based checking Server — file is uploaded Yes, Advanced/Premium licence Browser beta; single file up to 5 GB
Vecaria IFC Model Viewer Opens and parses the file; reports parse errors; measure, section, element tree, properties, takeoff, 2D plan Browser — file stays on your machine No A viewer, not a validator: it does not run validation rules or IDS

No single free browser tool covers all six layers. The practical combination is a viewer for layers 2 and 4 (open, inspect, spot-check) plus a validator for layers 3 and 4 (rules and IDS), with the buildingSMART service for layer 1 when a submission requires certified compliance.

IDS (Information Delivery Specification) is buildingSMART’s format for writing down what information a model must contain. An IDS file is a machine-readable checklist: it says, for example, that every wall must carry a fire rating property, that every door must have a classification code, or that all load-bearing elements must state their material. The receiver writes the IDS; the sender runs it against the model before delivery.

An IDS file contains specifications, and each specification has two parts: an applicability rule (which elements it applies to — for example, “all IfcWall elements”) and a requirement (what those elements must have — for example, “property FireRating is required”). A validator reads the IDS, tests every applicable element, and reports which specifications pass and which fail, element by element.

You do not need to write IDS by hand to start. IFC Viewer Online ships built-in validation profiles, including an ISO 19650 profile, and Bimlyte and the Model Checker both accept IDS files. If a project hands you an IDS file, run it; if it does not, the data-quality rules in a free validator are a reasonable stand-in for a first delivery.

Run through this list before every handover. Items 1–6 take a few minutes in a browser; items 7–8 need the project requirements.

# Check How
1 File parses with no errors Open in a viewer; read the parse report
2 GlobalIds present and unique Validator report (data-quality rules)
3 Project → site → building → storey chain complete Element tree / spatial structure view
4 Every element assigned to a storey Validator report or storey visibility check
5 No empty names; types assigned Element list scan
6 Units and project origin correct Model properties / viewer info panel
7 Required properties present IDS run, or validator data-quality rules
8 Classifications and materials as specified IDS run
9 No duplicate geometry in the same place Bounding-box overlap scan
10 File size and IFC version as agreed File properties; confirm IFC2x3 / IFC4 / IFC4x3

Can I validate an IFC file online for free? Yes. The buildingSMART Validation Service checks schema compliance for free (upload and account required). IFC Viewer Online and Bimlyte run data-quality rules and IDS checks entirely in the browser, free and without an account.

What is the difference between IFC validation and IFC checking? They are the same activity under two names. “Validation” usually means checking against a formal requirement — the IFC schema or an IDS file. “Checking” is the looser term, covering any review of a model’s quality. This guide uses “validation” for all of it.

Do I have to upload my model to validate it? Not for data-quality and IDS checks: IFC Viewer Online, Bimlyte, and the Model Checker all run in the browser, so the file never leaves your machine. Schema compliance via the buildingSMART service does require an upload, and so does Solibri WebChecker.

What is a good IFC health score? Health scores are tool-specific, so compare scores only within one tool. On IFC Viewer Online’s 0–100 scale, the public Duplex sample model scores 77 — a realistic, well-formed model rarely scores 100, because some rules encode strict delivery requirements rather than outright errors. Fix the failing items by priority, not the number itself.

Does validation replace clash detection? No. Validation checks one file against requirements. Clash detection compares two or more models (for example, architecture against MEP) and finds geometry that overlaps. They answer different questions, and a delivery usually needs both.

Which IFC versions can I validate online? The free browser tools generally support IFC2x3, IFC4, IFC4x1, and IFC4x3. If your file is IFC4x3 (infrastructure), confirm the tool supports it before you rely on the result — schema compliance for 4x3 is newer and not every checker covers it fully.

  • IFC Model Viewer — open an IFC file in the browser, measure, section, browse the element tree, and export a takeoff.
  • IFC Elements List — list every element in an IFC file with its type and properties.
  • IFC to GLB — convert an IFC model to GLB for use in 3D tools and game engines.
  • IFC Model Viewer documentation — details, limits, and how the viewer works.